Analog Frequency to V/I Converter

Looking for accurate analog conversion? The frequency to current converter available at Canopus Instruments will give you accurate analog conversion. The f to v converter manufactured by Canopus Instruments are of highest quality and standard. Get in touch with us to know the details of the products.

Download PDF

The SIM µ 2.0 Freq. to V/I converter accepts a Frequency Input and provides an optically isolated analog DC voltage or current output that is linearly proportional to the input frequency variation. The Frequency to V or mA converter provides very accurate analog conversion accuracies from 10% of input range onwards. Below this value of input frequency, the output analog value exhibits ripple due to the inherent limitation of the capacitive filter at the output at low frequency.

Product variant is available to accept Magnetic Pick UP (MPU) signal inputs.

Ordering Information

Isolation (I) Input Type Output Type Supply 24VDC (2D) I/P Signal Range I/P Amplitude Range O/P Signal Range Isolation MPU
Extension required for MPU signal
I I/P O/P Supply XX X XX 3P
I F VI 2D 0-1KHz:1 5V:5
12V:12
15V:15
24V:24
0-5V:05 3P MPU
0-5KHz:5 0-10V:10
0-10KHz:10 4-20mA:42
0-20KHz:20 0-20mA:20

Note:MPU, Extension use

Frequent Searches for F to V Converter

Frequency to Voltage Converter India, F to V Converter Pune, Frequency to Current Converter Bangalore, F to V Converter Mumbai, F to V Converter Ahmedabad, Frequency to Current Converter Hyderabad, Frequency to Current Converter Chennai, F to V Converter New Delhi, F to V Converter Nashik, F to V Converter Kolkata
Download PDF

  • Interfaces with Frequency Signal outputs of Proximity Switches.
  • Magnetic Pick Up (MPU) type sensor interface, designed to accept wide variations in input amplitude.
  • Slim & compact design.
  • Energy Efficient Module.
  • Accuracy 0.1% at 25°C From 10%-100% of Input range.
  • Low Noise & Low drift for long term stability.
  • 2kV 3 Port Isolation.

Applications

  • Speed sensing of Turbines and Motors, where conversion of pulsating Frequency signal output of a proximity switch/MPU Sensor is to be converted into Proportional analog value for indication or measurement.

 

Download PDF

Frequency Input Signal Input Options:0- 1KHz, 0-5KHz, 0-10KHz, 0-20KHz. Factory Set
Input Waveform Square Wave (24V Amplitude)
MPU Signal : Sine Wave
(1V to 28V Amplitude)
Impedance : 3KOhms
Impedance : 10KOhms
Output Signal Output Options:0- +5VDC, 0- +10VDC, 0-20mA, 4-20mA. Factory Set
Load Resistance For Output Voltage >1 K Ohm
For Output Current < 500 Ohm
Performance Accuracy ±0.1% of Span (10% -100% of Input range)
0.25% over operating temp. Range.
Linearity 0.1%
Temperature Drift <0.01% / °C
Calibration Zero & Span (Trimpot )

 

Download PDF

Isolation 2KV – 3 Port.
Power Supply Voltage 24VDC(nominal)
Operating Voltage 18-36VDC
Ripple <100mVpp
Power Supply Current 150mA.Max
Enclosure ABS Plastic, 35 mm DIN Rail Mounted. IP40 Protection class. Single Output W – 22.5mm
H – 75mm
D – 110mm
Operating temp. range 0 – 55°C
Storage temp. range 0 – 80°C
Relative Humidity 0 – 90%
RH Non-Condensing
Max. Altitude 3000 mts above MSL

 

Download PDF

Analog Frequency to Voltage / Current Converter - 24VDC Supply

Pin Details Pin Details
1 NC 5 +Output
2 +Input 6 -Output
3 -Input 7 +24Vdc
4 NC 8 GND

 

Download PDF

Additional information

Input Types

Frequency (Sq. Wave), Magnetic Pick Up (MPU) Sensor, Proximity Switch

Output Signal

Current 0-20/4-20mA (4 Wire), DC Voltage (+/-10V)

Supply

24VDC

Isolation Level

2 KV

Enclosure

ABS Plastic

Product Type

Converter

Reviews

There are no reviews yet.

Be the first to review “Analog Frequency to V/I Converter”

Your email address will not be published. Required fields are marked *

Translate »